 MSDS FOR ACS RESIN |
Information in this format is provided as a service to our customers and is intended only for their use. Others may use it at their own discretion and risk.
The MSDS format adheres to the People’s Republic of China standards and regulatory requirements and may not meet regulatory requirement in other locations.
This information is based upon technical information believed to be reliable. It is subject to revision as additional knowledge and experience are gained. |
| |
1, Chemical Product & Manufacturer’s Information |
| a. Chemical Product Name |
Acrylonitrile- Chlorinated Polyethylene -Styrene Terpolymer |
| b. Usage |
Electronic and Other Applications |
| c. Chemical Type |
Thermoplastics |
| d. Manufacturer’s Address |
No.39,Jinyi Road Xiaoshan Economic & Technological
Development Zone, Hangzhou City, Zhejiang Province People’s Republic Of China, 311215 |
| e. Phone / Fax Number |
Tel.: 86-571-82836915, Fax: 86-571-82832258 |
| f . Prepared By |
Hangzhou Keli Chemical Co., Ltd. |
|
2, Ingredients |
| |
CAS Number |
Percentage |
| a. ACS(Acrylonitrile- Chlorinated Polyethylene -Styrene) |
- |
85-95% |
| b. Typical Stabilizer |
- |
1-5% |
| c. Typical Lubricants |
- |
0-3% |
|
3, Physical & Chemical Character |
| a. Appearance |
Granule or Powder |
| b. Odor |
Almost Odorless |
| c. PH |
Neutral |
| d. Solubility in Water |
Insoluble |
| e. Solubility in other Solvent |
Soluble in DMF and other Analogous Solvents |
|
| 4, Health Hazard Data |
| a. Threshold limit |
| b. Effect of overexposure |
| • Eye Contact |
Solid or dust may cause irritation or corneal injury due to mechanical action |
| • Skin Contact |
Essentially nonirritating to skin, Mechanical injury only |
| • Skin Absorption |
Unlikely due to physical properties |
| • Ingestion |
Unlikely due to physical state |
| • Inhalation |
Dust may cause irritation to respiratory. In case of breathing, fumes released from heated material may cause respiratory irritation |
| • Chronic Effects |
Not Available |
| • Mutagenicity |
Not Available |
|
|
5, First Aid Measures |
| a. Eye Contact |
Immediately rinse eyes with copious amount of running water and seek medical advice |
| b. Skin Contact |
Essentially nonirritating to skin but rinse with copious water |
| c. Ingestion |
If vomiting occurs, lower the head to ease vomiting and seek for medical advice |
| d. Inhalation |
In case of breathing, fumes released from heated material may cause respiratory irritation
In case of inhaling dense smoke, immediately remove a person to fresh air. If necessary, apply artificial respiration and seek medical attention immediately |
| e. Mutagenicity |
Not Available |
|
| 6, Fire & Explosion Hazard Data |
| a. Flash Point |
Not Available |
| b. Flammability |
FV-0 |
| c. Auto Ignition Point |
Not Applicable |
| d. Extinguishing Media |
Usually use water and use extinguishing media appropriate to surrounding conditions |
| e. Special Fire Fighting Procedure |
Cool Containers with water spray. In closed stores, provide fire fighter with self-contained breathing apparatus in positive pressure mode |
| f. Usual Fire and Explosion Hazards |
Irritating gases and dense smoke |
|
| 7, Reactivity Data |
| a. Stability |
Stable under normal condition |
| b. Storage conditions to avoid |
Avoid fire and heating above 60℃ |
| c. Incompatibility |
None known |
| d. Hazardous decomposition products |
Not applicable |
| e. Hazardous polymerization |
Not occur |
|
| 8, Spill or Leak Procedures |
| a. Cleaning Method |
Sweep, use vacuum cleaner, or shovel into intact packaging for waste disposal or possible re-use |
| b. Waste Disposal Method |
Reuse or transfer to an approved disposal area.Observe all federal, state, or local regulations upon disposition. |
|
| 9, Special Protection Information |
| a. Handling |
Avoid formation of dust
Keep bags always closed / Keep container lightly closed
Avoid pellets / bags from getting wet |
| b. Storage |
Keep bags / container in a well-ventilated place
Avoid pellets / bags from getting wet |
|
10, Other Information |
Product should be handled, stored, and used in accordance with the generally accepted industrial hygiene practices and in conformity with all the applicable legal regulations.
The information provided herein is based on the knowledge possessed at this present time from the view point of safety requirements.
It should, therefore, not be construed as guaranteeing specific properties. |
| |
